2016年思科认证CCIE认证考试模拟试题及答案
思科认证主要考试内容是什么?今天yjbys小编为大家分享的是思科认证考试模拟试题及答案,仅供同学们复习参考!
1. Before inserting a new switch in the network, the network administrator checks that the VTP domain name is correct, the VTP mode is set to server, and revision is lower than the switches in the network. The administrator then configures interfaces and trunks, erases existing VLANs, and connects the switch to the network. Following that procedure, there is no connectivity in the network. What is a possible cause of this problem?
之前在网络中加入了一个新的交换机,网络管理员检查VTP域名是正确的。VTP模式设置为 服务器,修订号也比其他的交换机低。管理员配置接口和Trunk。清空了所有的VLAN后吧 交换机连接入网络。经过这些操作,交换机没有任何的网络连接。这是什么问题?
A. Because the configuration revision of the new switches is lower than the rest of the network, it can change the VLAN database of the other switches. B. As a VTP server, the new switch deleted all VLANs of the network. C. Erasing VLANs increases the VTP configuration revision.
清空VLAN 会影响到VTP的修订号
D. Since the configuration revision of the network is higher than the new switch, the VLAN database was automatically synchronized.
Answer: C
2. While deploying a new switch, you accidently connect ports 3/12 and 3/18 together, creating a loop. STP detected it and placed port 3/18 in blocking mode. Why did STP not place port 3/12 in blocking mode instead?
当部署一个新的交换机,你无意的链接了3/12/和3/18,形成了一个环路,STP把3/18端口 设置为阻断端口,为什么没有把3/12设置为阻断端口呢?
A. Port 3/12 was already up and forwarding before the loop was created. B. Port priority is based on lowest priority and lowest port number. 因为端口ID 3/12比较低 C. You connected the wire on port 3/18 last. D. None of the above, it is purely random. Answer: B
3. Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correct BGP session endpoint addresses and the correct BGP session hop-count limit (EBGP multihop). What is a good first test to see if BGP will work across the firewall?
有两个运行BGP的路由器连接到防火墙, 一个在inside接口, 一个在outside 接口。 BGP 已经配置并且已经成为了邻居,包含正确的配置了BGP网络地址和正确的BGP跳数的限制 (EBGP的多跳设置),怎么能够最好的测试BGP工作在防火墙上。
A. Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works, BGP will work, since telnet and BGP
both use TCP to transport data.
用在inside接口上的路由器telnet 到在outside 接口上的路由器。如果telnet 正常工作侧说明 BGP能正常工作,因为telnet 和BGP 都是使用TCP 来传输数据的
B. Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them, BGP should work, since BGP uses IP to transport packets. C. There is no way to make BGP work across a firewall without special configuration, so there is no simple test that will show you if BGP will work or not, other than trying to start the peering session. D. There is no way to make BGP work across a firewall.
Answer: A
4. Refer to the exhibit. In this network, R1 has been configured to advertise a summary route, , to R2. R2 has been configured to advertise a summary route, , to R1. Both routers have been configured to remove the discard route (the route to null created when a summary route is configured) by setting the administrative distance of the discard route to 255.
如图所示,在这个网络中,R1通告了的'汇总路由给R2, R2通告了的汇总路由给R1。两台路由器都配置了汇总路 由的null0 接口来防止路由的环路。发生什么情况,R1能收到一个去192.16 8.3.1的数据包?
What will happen if R1 receives a packet destined to ? A. The packet will loop between R1 and R2. 这个包在R1和R2之间形成了环路 B. It is not possible to set the administrative distance on a summary to 255. C. The packet will be forwarded to R2, where it will be routed to null0. D. The packet will be dropped by R1, since there is no route to .
Answer: A
5. Refer to the exhibit. In this network, R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP?
如图所示,在这个网络中 R1配置为在EIGRP中不做自动汇总,那么R3能从R2学到什么 EIGRP的路由信息。
A. and ; EIGRP only performs autosummarization at the edge
between two major
和 EIGRP在两个较大的网络边缘只能执行自动汇总。
B. and ; R2 will perform autosummarization, although R1 will not. C. Since R2 is configured without autosummarization, it will not propagate the route. D. and Answer: A
-
思科LINKSYS 宽带无线路由器设置方法
在无线上网的过程中,由于无线路由器设置发生错误导致网络连接失败或者出现其他故障比比皆是。那么,如何设置Linksys无线路由器呢,具体解决方法如下:一、Linksys路由器Linksys的出厂隐含设置,登录名和密码都是admin,Linksys的AP常见有WAP54G、LinksysWAP11,只有无线台...
-
思科路由器设置VPDN的方法
CCNA重新认证:CCNA认证证书的时效性是三年。要重新更新证书,必须通过CCNA的考试(如果通过的下一阶段CCNP的考试,CCNA认证证书会被自动更新)下面是小编整理的关于思科路由器设置VPDN的.方法,欢迎大家参考!1启用aaanew-modelaaanew-model2、建立认证方式aaaauthentic...
-
思科电信运营商核心网络运营基础考试大纲
思科电信运营商核心网络运营基础(OFCN)考试是与CCNPSP运营认证相关的.考试。该考试主要检验考生在电信运营商网络运营环境方面的知识,重点关注与第二层和第三层网络运营有关的中-高级流程管理、NMS工具和故障排除技能。ExamDescriptionThe642-770OperationalFou...
-
cisco常用命令大全
为帮助大家更好通过思科认证。yjbys小编为大家分想的是思科认证基本命令,欢迎参考阅读!路由器的几个基本命令:Router>enable进入特权模式Router#disable从特权模式返回到用户模式Router#configureterminal进入到全局配置模式Router(config)#interfaceethernet1进...